Open Access Open Access  Restricted Access Subscription or Fee Access

Development of Grinding Wheel Using Nano-Materials

S. Selvan Nambi, P. Ranjith Kumar

Abstract


An attempt has been in the present work to fabricate a grinding wheel using nano particles. Traditionally alumina plays a vital role in grinding wheels, hence alumina nano particles were successfully synthesized. For synthesis of alumina nanoparticles ball milling process was used. Nano alumina particles of 30nm were synthesized at 40 hours. The material grain size and composition was confirmed using SEM and EDAX. Using these nano alumina particles a grinding wheel was formed by combining micro-sized Alumina with bond (Nano Alumina) and binders (Dextrin).

Keywords


Alumina, Ball Milling, EDAX, Nanoparticles, SEM.

Full Text:

PDF

References


M.I.Martı´n , L.S. Go´mez a, O. Milosevic b, M.E. Rabanal a,“Nanostructured alumina particles synthesized by the Spray Pyrolysis method: micro structural and morphological analyses”,2009, pp767-772

F. Mirjalili a,*, M. Hasmaliza b, L. Chuah Abdullah “Size-controlled synthesis of nano a-alumina particles through the sol–gel method” 2010, pp1253-1257

J.M. Wu“Nano-sized amorphous alumina particles obtained by ball milling Zn and Al powder mixture”2007, pp 324-330.

Carsten Schilde , Hendrik Nolte , Christine Arlt , Arno Kwade ,“Effect of fluid–particle-interactions on dispersing nano-particles in epoxy resins using stirred-media-mills and three-roll-mills‟‟2010,pp 657–663

S. Biamino , P. Fino, M. Pavese, C. Badini ,“Alumina–zirconia–yttria nanocomposites prepared by solution combustion synthesis”2005, pp 509-513.

Sheng Guo, Apichart Limpichaipanit , R.I. Todd,“High resolution optical microprobe investigation of surface grinding stresses in Al2O3 and Al2O3/SiC nanocomposites”2011,pp 97–109

Przemyslaw Byszewski , Hubert Lange,Andrzej Huczko and jurgen f. Behnke “Fullerene And Nanotube Synthesis. Plasma Spectroscopy Studies”,1955,pp 1679-1683

M.I.Mart´ın, M.E.Rabanal, L.S.G´omeza, J.M.Torralba, O.Milosevic ,“Micro structural and morphological analysis of nanostructured alumina particles synthesized at low temperature via aerosol route”, 2008,pp 2487–2494

Peter Jevnikara, Kristoffer Krnelb, Andraˇz Kocjanb, Nenad Funduka, Tomaˇz Kosmaˇc, “The effect of nano-structured alumina coating on resin-bond strength to zirconia ceramics”2010, pp 688-696.

M. Shojaie-Bahaabad, E. Taheri-Nassaj ,“Economical synthesis of nano alumina powder using an aqueous sol–gel method.”2008, pp 3364-3366.

Rajalekshmi Chockalingam, Vasantha R.W. Amarakoon, Herbert Giesche,”‟Alumina/cerium oxide nano-composite electrolyte for solid oxidefuel cell applications” 2008,pp 959–963

S. Gustafsson a, L.K.L. Falk a, E. Lide´n b, E. Carlstro¨mb ,“Alumina/silicon carbide composites fabricated via in situ synthesis of nano-sized SiC particles”2009, pp1293-1296

Bin Li , Hong Wang , Jianxin Deng , Jiadong Chang , Hongtao Zhang “Antifriction characteristics of quasi-nano alumina reinforced with Zr–O–B compounds against cemented carbides”,2011, pp177–183

Xuesong Hana,, Yong X. Ganb, “Analysis the complex interaction among flexible nanoparticles and materials surface in the mechanical polishing process”2011,pp 3363–3373.

Gyuhae Park,, Matthew T. Bement, Daniel A. Hartman, “The use of active materials for machining processes: A review”2007,pp 2189–2206

Tung-Hsu Hou, Chi-Hung Su , Wang-Lin Liu, “Parameters optimization of a nano-particle wet milling process using the Taguchi method, response surface method and genetic algorithm”2007,pp153–162


Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution 3.0 License.